How to Configure Linksys WRE54G Range Expander - Tom’s Guide. I followed the instructions to get it connected by turning off wireless security, using the auto-config button, connecting to the RE and changing the security settings, then turning wireless security back on. I would choose an entirely different range. Basically, you find a location from which it gets a good signal from the router, and from which the computer gets a good signal from the range expander. I purchased a Linksys WRE54G range extender and placed it about halfway between the router in order to take the signal to the last mile. It’s also usually printed on a label somewhere on the outside of the product. ask a new question. They are on the same network ip range but not physically (via wireless) connected. Antenna Make sure the antenna is positioned straight up into the air, no matter how the Range Expander is positioned. I don't fool with a lot of consumer devices like this and it's completely taken me off my game with no error logs or anything like that to troubleshoot with. You will receive a verification email shortly. Wait at least 10 seconds to make sure that the WRE54G successfully got the message, then force the wireless client to connect back to the main AP,set your wireless client back to being a DHCP client and successfully get an IP address and proper Gateway and DNS information. I had a WRT54g lying around and used that to do the same thing you did. New York, © It is setup with 64 bit WEP and forced to G. What am I missing? I followed the instructions to get it connected by turning off wireless security, using the auto-config button, connecting to the RE and changing the security settings, then turning wireless security back on. 00:0e :ef :fd :a2:3c. You plug it in, turn it on, and connect the computer to the range expander's signal. Well actually the DD-WRT gives it more capabilities then the original firmware. The last post with promise suggested that his did the same thing, but he got this behavior when the RE was moved too far away from the router. The Range Expander has been configured to run on channel 1 with an IP address of 192.168.1.240 with a netmask of 255.255.255.0. Couple of months ago my dad complained that his signal is not strong enough out in the back yard. This article will guide you on how to access the web-based setup page of your Linksys WRE54G Wireless-G Range Expander using a Windows -based computer. It sounds as your RE is not connecting to your home Wireless Router. Try to avoid defaults, use something like 192.168.254.254 This should be set on the main router. Category: Networking. H Enter the Range Expander’s default password, admin, and click Enter. Tom's Guide is part of Future US Inc, an international media group and leading digital publisher. This person is a verified professional. to enable IT peers to see that you are a professional. If your WLAN doesn’t use the 192.168.1.X subnet, leave the wireless client set to the static IP you’ve used so far, force the wireless client to directly connect back to the WRE54G and change the WRE54G’s IP address and Gateway to match your LAN’s setup. I have combed Google for anything related to it and actually found a few posts referring to the exact equipment models involved. LEDs LINK Blue/Red. You’ll need to get this information from the target AP’s admin screens. Wireless-G Range Expander Chapter 3: Getting to Know the Wireless-G Range Expander The Front Panel The Range Expander's adjustable antenna, LEDs, and Ethernet network port are located on the front panel. I set a manual IP and was able to connect, but got no network connectivity. Receive news and offers from our other brands? Current page: on I Enter an IP Address and appropriate Subnet Mask. Also WRT54G is more versatile, if you don't have the need to have a bridge anymore you can still use it as a regular router. The only other setting you need to change is to enter the MAC address of the target AP / wireless router into the Access Point MAC address box. Linksys' WRE54G Wireless-G Range Expander [reviewed here] is a WDS-based 802.11b / g repeater that Linksys says works only with its WAP54G access point and WRT54G and WRT54GS wireless routers. If you’re enabling WEP, make sure you set up the WRE54G first, then make the the corresponding changes on your wireless client. There was a problem. (Some wireless networks may require additional security settings, such as that shown in Step F, at this time.) I purchased a Linksys WRE54G range extender and placed it about halfway between the router in order to take the signal to the last mile. 1) Turn off WEP or WPA on your router 2) Plug the WRE54G in the same room as your router 3) Push autoconfig button and hold 5 seconds. To continue this discussion, please Verify your account Linksys' WRE54G Wireless-G Range Expander [reviewed here] is a WDS-based 802.11b / g repeater that Linksys says works only with its WAP54G access point and W... How To: Manually Setting Up the Linksys WRE54G Wireless-G Range Expander - SmallNetBuilder